www.tomyang.net

Never even noticed my cavallino stance ! I have a Becker Europa II stereo, and you can purchase these DIN plugs that plug into the rear service port on all vintage Becker and Blaupunkts attached are pics- all over ebay or from the Becker place in NJ. You attach a cable from your iPhone headphone jac...

you can also buy used one from MG 1961-1967- its the same Smith part. I got one on ebay for like 40$.
michael

awesome. thats sort of what I thought but wanted confirmation!
the good news ?.... nothing else on the list to worry about.~!
Thanks

We have had 2 miserable weeks of rain. This weekend I had to go about 80 miles East of Atlanta to a meeting, and weather was scheduled to be perfect, but cool all weekend. Took the opportunity to drive the 330 about 300 KM, without a hitch. Drove like a new car. An absolute blast. However, the oil a...

When you find out , pls post as I have a small area when someone did the same thing.I think the mid 60s corvettes used a 2 part epoxy resin with the fiberglass so likely thats what Ferrari used. Bondo also makes "fiberglass resin". here is a pic of the bottom of my console---- is this the color and ...

although I havent done it, a cheap way may be to use a 70s mercedes jack like the one attached. I never had a problem with them; smooth operating, sturdy, but you would use the original jack hole if you went this route. the long post always provided some security. the post on my 190SL jack is good c...

pertronix has a few models- Pertronix MR-1121A Ignitor Ignition Module for a 6 lobed cam, and a different model ( I think its 1122 ) for 3 lobed cam. the issue is you need to change the resistance if you go pertronix- too much current and they burn out apparently (I spoke with the engineers after re...

When I purchased my car, the original AZ owner had already redone the AC in the 70s, with a custom bracket for compressor, moving the condenser in the front behind the grill. It no longer worked, and Sanden type wont fit, so I went about replacing items with R134. Only took me a weekend to get it al...

i re-did all my fuel hoses and covered the ones by my facet pump ( which I run all the time) with Earl's Flame Guard. see attached pics.. silica covered fuel resistant heat protection sheathing. Also made a new heat shield and covered it with a reflective material from a speed shop. Actually works w...

john, i did warm them up a bit with a heat gun, but the fact is because they are 2 pieces of aluminum sandwiched together with thin layer or air in the middle, they really didn't heat up that much. just warm. the key was hanging them outside in the southern exposure atlanta sun in july. for the firs...

just an update on VHT wrinkle paints- lot of forum discussion re different vendors ( wurth, vht, eastwood etc) . here are some actual pics of my heat shield which I re-did yesterday. getting it clean and prepped was key. matches really well with the valve covers. product went on great, just followed...

330-GT-AC-bracket.jpg 330-GT-AC-bracket-(1).jpg Dan since my condenser is already in a non-eom location in front of the fans and horns, I am not concerned about the originality. I am going for performance. the mods made by the owner appear very thought out. I pulled everything - see pic of the cust...

dan, not sure about that but my AC guys said the serpentine type ( like mine pictured ) are not as efficient as the new parallel flow condensers, so I am going to replace mine. also, the new ones have real fittings, not the push on type, and are less prone to leaking. Once I get it all done, I will ...

Enzo with his 330 and fog lights. I think am going back to how my car was equipped when it was with its long term Arizona engineer owner!

As I was pulling my AC parts, I came across an unattached harness near the drivers front behind the grill. it is held in my one of those old metal ties. It is powered by the switch shown in the pic near my front door jamb (which by the way I only found today after discovering the wiring harness and ...