Hi Tom,
Thanks for your time and effort. Although they are somewhat simular they are too different for my needs.
Thanks again
Giovanni
Search found 74 matches
- Sun Oct 31, 2010 7:34 pm
- Forum: Vintage Ferraris
- Topic: Water Pump
- Replies: 3
- Views: 3154
- Sun Oct 31, 2010 4:43 pm
- Forum: Vintage Ferraris
- Topic: Water Pump
- Replies: 3
- Views: 3154
Water Pump
To all,
Does anyone have an exploded view of the water pump for the Series II 330 2+2 engines that they could pass along ? Either actual pictures or pictures from a manual would be fine.
Thanks,
Giovanni
Does anyone have an exploded view of the water pump for the Series II 330 2+2 engines that they could pass along ? Either actual pictures or pictures from a manual would be fine.
Thanks,
Giovanni
- Thu Oct 28, 2010 4:43 pm
- Forum: Vintage Ferraris
- Topic: Cooling System Part Finishes/Colors
- Replies: 31
- Views: 24554
Re: Cooling System Part Finishes/Colors
Hello,
Would electrolysis be a concern when the part in question is insulated or isolated by rubber hoses and gakets? Perhaps there is something I am not aware of.
Giovanni
Would electrolysis be a concern when the part in question is insulated or isolated by rubber hoses and gakets? Perhaps there is something I am not aware of.
Giovanni
- Sat Oct 09, 2010 10:12 am
- Forum: Vintage Ferraris
- Topic: 33GTC Suspension
- Replies: 15
- Views: 13213
Re: 33GTC Suspension
To Jim and John,
As a GTC owner I am extremely interested your post(s), however when attempting to download the pics I was unable to do so. Must I have a photo bucket account to view those pics?
Regards,
Giovanni
As a GTC owner I am extremely interested your post(s), however when attempting to download the pics I was unable to do so. Must I have a photo bucket account to view those pics?
Regards,
Giovanni
- Thu Sep 02, 2010 8:44 am
- Forum: Vintage Ferraris
- Topic: License Plate Mounting
- Replies: 2
- Views: 2637
Re: License Plate Mounting
My car`s PO was in England, so there were no mountings at all. The information and pictures you sent were exactly what I was looking for. Thank you very much!
Giovanni44
Giovanni44
- Wed Sep 01, 2010 10:40 am
- Forum: Vintage Ferraris
- Topic: License Plate Mounting
- Replies: 2
- Views: 2637
License Plate Mounting
To all, I am interested in obtaining pictures of the rear license plate mounting brackets for the 330GT 2+2. From when the car was purchased, my plates were attached directly to the body,which to me, does not seem to be the typical Ferrari practice. Comments,suggestions appreciated also. Thanks in a...
- Mon Aug 30, 2010 5:14 pm
- Forum: Vintage Ferraris
- Topic: clock knob
- Replies: 0
- Views: 3482
clock knob
Someone was looking for a knob for setting the clock, I have one for the 330 GT 2+2,which may fit others too ?? . Please PM me if interested.
Giovanni44
Giovanni44
- Wed Aug 18, 2010 5:28 am
- Forum: Vintage Ferraris
- Topic: nead lead for carpeting
- Replies: 6
- Views: 5189
Re: nead lead for carpeting
Hello Al,
Have you tried Bill Hirsch or World Upholstery ? Typing in either of these names will get you their web site.
Giovanni 44
Have you tried Bill Hirsch or World Upholstery ? Typing in either of these names will get you their web site.
Giovanni 44
- Wed Aug 11, 2010 11:24 am
- Forum: Vintage Ferraris
- Topic: 250 Pinion Bearing Installation
- Replies: 10
- Views: 8092
Re: 250 Pinion Bearing Installation
Hello Roger, Have you measured the new bearing and compared that measurement to that old bearing? Bearings have a bearing fit( sometimes refered to as a press fit )in their housing of only .00025" to .0005" at most and if that is exceeded you will have problems. Measure all the critical dimensions, ...
- Sun Aug 01, 2010 1:44 pm
- Forum: Vintage Ferraris
- Topic: Engine compartment trim
- Replies: 3
- Views: 3672
Re: Engine compartment trim
jroswell, Upon opening the hood, there is a channel surrounding the engine compartment. The inside edge of that cannel is the seam formed by the seam of the inside and outside fender joint. That joint is covered by an inverted "U" shaped black plastic/rubber trim strip. My question is, should that s...
- Sat Jul 31, 2010 3:29 pm
- Forum: Vintage Ferraris
- Topic: Engine compartment trim
- Replies: 3
- Views: 3672
Engine compartment trim
To all, Can anyone tell me if the engine compartment trim on late(just prior to 365 GTC series) 330 GTC has a textured finish or is it plain with no pattern? On the 365 GTB-Daytonas this trim had kind of a miniture tire tread pattern. So, my question is, were any of the later production 330 GTC`s pr...
- Thu Jul 01, 2010 5:05 pm
- Forum: Vintage Ferraris
- Topic: Brake Caliper Mount
- Replies: 3
- Views: 3464
Brake Caliper Mount
Can anyone out there tell me if the front brake caliper mount is supposed to be plated or painted? I am refering to the casting/forging to which to front brake caliper cylinders attach.
Thanks,
Giovanni44
Thanks,
Giovanni44
- Sat May 22, 2010 11:31 am
- Forum: Vintage Ferraris
- Topic: Brake Rebuild
- Replies: 1
- Views: 2094
Brake Rebuild
Hello Tom, First of all,thanks for creating and maintaining this valuable website! :D I noticed on your latest post of the return of your brake cylinders from Karp`s showing the cylinders sleeved. Did you have any additional work done such as plating and replacing the seals and re-assembly or did yo...
- Sat Nov 14, 2009 1:04 pm
- Forum: Vintage Ferraris
- Topic: Oil Filters
- Replies: 17
- Views: 13231
Re: Oil Filters
It seems that in rereading my previous posts and the corresponding replies, it appears that I am not posing my inquiry clearly. What I am looking for is information on how other owners have delt with eliminating or reducing the oil spill created when changing the left hand oil filter on the 330 GTC....
- Fri Nov 06, 2009 1:59 pm
- Forum: Vintage Ferraris
- Topic: Oil Filters
- Replies: 17
- Views: 13231
Re: Oil Filters
In preparation for winter storage, I changed the oil and filters on my GTC. As both of the filters are Fram PH2804-1, the driver’s side filter always presents a problem in that as soon as you remove the filter all the oil contained in the filter empties itself creating a clean up problem in spite of...