Switch clips needed
-
- Posts: 699
- Joined: Mon Nov 04, 2002 7:22 am
Switch clips needed
Does anyone know a souce for the metal clips that attach to the side of the power window switches and serves to hold the switch in place in the console? They also hold the plastic switch body in the chrome surround, M
Michael J. Bayer
330GT s/n 9727
365GTC4 s/n 14943
Dino Spider s/n 1193
330GT s/n 9727
365GTC4 s/n 14943
Dino Spider s/n 1193
Re: Switch clips needed
I tried (not too successfully) to make some. Count me in for several if you find a source.
Regards, Kerry
http://www.330gt.com 330 GT Registry
http://www.parrotbyte.com/kbc/ferrari 250 PF Coupe 1643GT, 330 GT 2+2 8755GT, 308 GTS 23605
http://www.330gt.com 330 GT Registry
http://www.parrotbyte.com/kbc/ferrari 250 PF Coupe 1643GT, 330 GT 2+2 8755GT, 308 GTS 23605
Re: Switch clips needed
Can u post a pic of what you need?
Ed Montini
330 GT 2+2 Series II - 8289
58 Ellena - 0855GT - orig drivetrain
87 El Camino SS
330 GT 2+2 Series II - 8289
58 Ellena - 0855GT - orig drivetrain
87 El Camino SS
Re: Switch clips needed
These fit on the underside of the switch (4 in all) and spring out to hold the switch in the console.
- Attachments
-
- WindowSwitch.jpg (19.42 KiB) Viewed 6926 times
Regards, Kerry
http://www.330gt.com 330 GT Registry
http://www.parrotbyte.com/kbc/ferrari 250 PF Coupe 1643GT, 330 GT 2+2 8755GT, 308 GTS 23605
http://www.330gt.com 330 GT Registry
http://www.parrotbyte.com/kbc/ferrari 250 PF Coupe 1643GT, 330 GT 2+2 8755GT, 308 GTS 23605
Re: Switch clips needed
There are spring shops that do small quantity runs. Might be worth dropping by one with a sample and seeing what a couple of dozen would cost. Here is one shop, local to Kerry: Sound Spring (http://www.soundspringinc.com). Haven't used them myself, but ran across them when I was looking for custom springs for a project. Many more shops can be found on Google.
Todd
Todd
-
- Posts: 98
- Joined: Sat May 16, 2009 5:31 pm
Re: Switch clips needed
I made some clips by using clip nut #853 which is for ford headlamp to fender. I had to grind them for sizing and most important to file down lock tab on inside of short tab otherwise it would cause too much pressure on bezel when switch is pushed down into place.
- Attachments
-
- DSC_0987clips.jpg (16.1 KiB) Viewed 6668 times
-
- Posts: 98
- Joined: Sat May 16, 2009 5:31 pm
Re: Switch clips needed
sorry that I have to do these one at a time, I don't have the hang on posting pictures yet, here's a picture with clips installed.
- Attachments
-
- DSC_0988 switch clips.jpg (17.71 KiB) Viewed 6666 times
-
- Posts: 98
- Joined: Sat May 16, 2009 5:31 pm
Re: Switch clips needed
Also I reproduced the plastic body that holds the switch in place that has the pivot point for the switch, as you can see that the pivot point on the plastic body is broken therefore causing the switch to cock and get stuck in operation. If anyone has this problem and would like for me to try to fix it, let me know.
- Attachments
-
- DSC_0986switch.jpg (17.04 KiB) Viewed 6665 times