GTE Fuel tank installation

Moderators: 330GT, abrent

BobA
Posts: 71
Joined: Tue Nov 12, 2013 7:36 pm

GTE Fuel tank installation

Postby BobA » Mon Jan 08, 2018 7:44 pm

I am in the process of re-installing my Series I tank and am wondering if there are any "secrets" to the the process. I have fitted the filler neck to the body and now realize that the angled tube fits inside the fuel tank filler rather than just connecting with the hose and clamps. Space is almost non-existent to move the tank from side to side and maybe the fitting of the fill pipe to the tank occurs while raising the tank up from below. Any advice? Thanks in advance. Bob #2693

User avatar
John Vardanian
Posts: 1673
Joined: Wed Sep 04, 2002 12:13 am
Location: San Francisco Area

Re: GTE Fuel tank installation

Postby John Vardanian » Wed Jan 10, 2018 1:20 am

Dissimilar car, but in my case the tank goes up in place first, then the rubber hose slips on the mouth of the tank (along with the clamps) then the filler neck slips inside the hose. The insulation grommets decide the vertical positioning of the tank, so if your tank is too far up then I can see why the mouth and the filler neck collide.

john
PF Coupe

BobA
Posts: 71
Joined: Tue Nov 12, 2013 7:36 pm

Re: GTE Fuel tank installation

Postby BobA » Wed Jan 10, 2018 4:14 pm

Since I did not realize that the filler pipe goes into the filler neck of the tank, I may have made the error of trying to push the tank up and then insert the filler pipe. I will lower the tank and try again when my son comes to help.Probably better with 2 people. Thanks John.

User avatar
tyang
Posts: 3662
Joined: Wed Nov 27, 2002 10:28 pm
Location: New York
Contact:

Re: GTE Fuel tank installation

Postby tyang » Wed Jan 10, 2018 5:34 pm

Hi Bob,

Yeah, Tank goes in first. Some cars have more room than others, but as in your case, the filler neck sounds like it's real close to the tank. Getting the big rubber grommet in place with the tank and filler neck lined up may be your next challenge. Heating up the rubber so it's pliable helps. Don't forget to connect the breather hose to the tank before you send the tank up into the bodywork!

Good luck!

Tom
'63 330 America #5053

BobA
Posts: 71
Joined: Tue Nov 12, 2013 7:36 pm

Re: GTE Fuel tank installation

Postby BobA » Wed Jan 10, 2018 9:20 pm

Thanks Tom: I have a section of 2" fuel filler hose, but realize that although I can fit it over the filler neck, it is too tight to slide up and back after aligning the filler pipe with the tank neck. Where can I buy a section of 55 mm ID fuel hose? GT Parts has 53 mm, but think that is also too tight. Bob

User avatar
John Vardanian
Posts: 1673
Joined: Wed Sep 04, 2002 12:13 am
Location: San Francisco Area

Re: GTE Fuel tank installation

Postby John Vardanian » Thu Jan 11, 2018 1:27 am

Bob, the 53mm hose is your average 2" hose presented as a metric hose. The best you can do is 2-1/8", which will work fine. Can you reuse the original?

john
PF Coupe

BobA
Posts: 71
Joined: Tue Nov 12, 2013 7:36 pm

Re: GTE Fuel tank installation

Postby BobA » Thu Jan 11, 2018 1:46 pm

Hi John: I cut the old one off, but would not have trusted it anyway. My regular hose supply house does not have and 2 1/8" hose, but I understand that a 1997 vintage VW Vanagon uses 55 mm ID hose in the fuel filler. Will try that route and will keep you posted. Bob

User avatar
John Vardanian
Posts: 1673
Joined: Wed Sep 04, 2002 12:13 am
Location: San Francisco Area

Re: GTE Fuel tank installation

Postby John Vardanian » Fri Jan 12, 2018 1:15 am

Bob, McMaster Carr has it.

john
PF Coupe

BobA
Posts: 71
Joined: Tue Nov 12, 2013 7:36 pm

Re: GTE Fuel tank installation

Postby BobA » Fri Jan 12, 2018 4:10 pm

Thanks John. I missed the Buna-n hose since it was listed as coolant hose. Ordered. Part # 572K54


Return to “Vintage Ferraris”

Who is online

Users browsing this forum: No registered users and 4 guests